There are many ways of connecting the NX-584/NX-8E panel's serial interface with a serial port on the Vera. NX-584 connection The NX-584 has a male DB9 serial interface. To connect the interface to another computer, either:. Use a female-to-female null modem cable, which swaps RX/TX and CTS/RTS to allow connection to a computer with a serial port, or. Use a female-to-female gender changer, and adjust the jumpers on the NX-584/NX-8E board to make it swap RX and TX pins and RTS and CTS pins. The important thing to remember is that you have to cross over the RX and TX wires exactly once, and the CTS and RTS wires exactly once; this can be done either with a null modem cable or by swapping the jumpers on the NX-584 board. NX-8E connection The NX-8E has a somewhat-standard 2x5-pin serial interface on the main board.

1. Serial Interface Cable (xy-rs-23a) 6 Foot Long

Find great deals on eBay for serial interface cable and trs-80. Shop with confidence. Installation Instructions for. The Omni Z-Wave Interface – Serial Kit includes: 1 x Vera 3. Connect the Ethernet cable between the Vera and your. Vera Controller. Created by hek. Configuring the Vera Plugin for the Serial/USB. To one of your Vera USB ports using a standard USB cable. If all of the Vera.

The is: NX-8E pin 3: RX (DB9 pin 2) NX-8E pin 5: TX (DB9 pin 3) NX-8E pin 9: Ground (DB9 pin 5) NX-8E pin 4: RTS (DB9 pin 7) NX-8E pin 6: CTS (DB9 pin 8) In some parts of the world Caddx sells a cable with these connections. Third-party 10-pin serial cables might have the same pinout. Otherwise you can make one yourself. You still need to cross over the RX/TX pair of wires and to cross over the RTS/CTS pair of wires exactly once; this can be done either with a null modem cable or by swapping the jumpers on the NX-8E board (does the NX-8E have jumpers?) or by wiring your DIY cable with the pairs swapped at one end. Extending the serial line The Vera and the Alarm panel might not be in the same room.

You can add a female-to-male straight DB9 serial cable onto the end to make the serial connection as long as you like. Alternatively, if your alarm panel is close to an Ethernet connection, you can connect an IP-to-serial bridge (either a dedicated adapter like the or a computer running ser2net). Connecting Vera to the serial line To connect the Vera directly, get a USB-to-serial adapter and plug it in. Alternatively, if you have installed an IP-to-serial bridge, set up an on Vera.

Cables After you install the serial WIC, use the appropriate serial cable to connect the WIC’s serial port to one of the following types of equipment. (See.):. An asynchronous modem, if connecting to an analog telephone line. A synchronous modem, DSU or CSU, or other DCE, if connecting to a digital WAN line The 1-port serial WIC has a DB-60 serial port, whereas the 2-port serial WIC and the 2-port A/S WIC have Cisco smart serial ports. Use the correct cable for your serial WIC.

Serial Interface Cable (xy-rs-23a) 6 Foot Long

The serial cable attached to a smart serial port determines the port’s electrical interface type and mode (DTE or DCE). Types of Cables for 1- and 2-Port Serial WICs Six types of serial cables (also called serial adapter cables or serial transition cables ) are available from Cisco Systems for 1- and 2-port serial WICs:. EIA/TIA-232 serial cable assembly. EIA/TIA-449 serial cable assembly. V.35 serial cable assembly.

X.21 serial cable assembly. EIA/TIA-530 serial cable assembly. EIA/TIA-530A serial cable assembly All serial cables provide a universal plug at the interface card end. The network end of each cable provides the physical connectors most commonly used for the interface. For example, the network end of the EIA/TIA-232 serial cable is a DB-25 connector, the most widely used EIA/TIA-232 connector. All serial interface types except EIA-530 are available in DTE or DCE format: DTE with a plug connector at the network end and DCE with a receptacle at the network end. V.35 is available in either mode with either gender at the network end.

EIA-530 is available in DTE only. LED Status Due to the high port density on the HWIC front panels, the amount of LED status per port is limited. There is no room for individual LEDs to indicate transmit or receive activity, or clock status. HWIC-4T and HWIC-4A/S have a single bi-color LED to monitor status over four ports.

HWIC-8A has a single LED to monitor status over 8 ports. There are two LEDs on the HWIC-8A/S-RS232 that monitor 4 ports each. On the HWIC-16A, two LEDs monitor 8 ports each. See for the definition of HWIC LED Status.

Cables After you install the serial HWIC, use the appropriate serial cable to connect the HWIC ports to the following types of equipment:. Asynchronous modems, if connecting to analog telephone lines.

Synchronous modems, data service units/channel service units (DSUs/CSUs), or other DCEs, if connecting to digital WAN lines The 4-port serial HWICs have 26-pin 12-in-1 Cisco smart serial ports, whereas the 8- and 16-port serial HWICs have 68-pin serial ports. Use the correct cable for your serial HWIC. Cables for 4-Port Serial HWICs The 4-port serial HWICs use Cisco smart serial cables. Six types of smart serial cables are available:. EIA/TIA-232 serial cable assembly. EIA/TIA-449 serial cable assembly. V.35 serial cable assembly.

X.21 serial cable assembly. EIA-530 serial cable assembly. EIA-530A serial cable assembly All of these serial cables provide a 26-pin plug at the interface card end. The network end of each cable provides the physical connectors most commonly used for the interface. For example, the network end of the EIA/TIA-232 serial cable is a DB-25 connector, the most widely used EIA/TIA-232 connector.

See for network end connectors and pinouts of these cables. The EIA-530 and EIA-530A serial cables are available in DTE format only. All other cables are available in either DTE or DCE format.

Related Documentation Related documentation is available on Cisco.com or on the Product Documentation DVD. For more information, see the., tech note., tech note., tech note. “ ” chapter of the Cisco 1700 Series Router Software Configuration Guide. “Configuring Serial Interfaces” chapter of the Cisco IOS Interface Configuration Guide for your Cisco IOS software release., Cisco IOS Release 12.2(2)T feature module., Cisco IOS Release 12.1(1)T feature module., sample configuration., sample configuration., sample configuration., sample configuration., sample configuration., sample configuration.

Approximatrix Simply Fortran 2.35 Full Version Features: Just Fortran for Windows can deliver both 32-bit and 64-bit code with its included compiler. Both targets are accessible on all Windows stages. The debugger incorporates the capacity to include breakpoints and screen certain expressions while running the program.